Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Rear Ride Height Adjustment
Porsche 924/944/968 rear ride height can be lowered (in most cases) by approximately ¾" using the following procedure. This adjustment was originally designed for factory ride height settings across |
Ride Height Measurement
Torsion Bar Indexing 101
The outside has 44 splines (teeth)
Every tooth you move the outside splines you move the spring plate about 9 degrees.
The inside has 40 splines (teeth)
Every |
Front Torsion Bars (65-89)
Author: Skip
Jack up the car and remove the front wheels. Remove the tow hooks that secure the front of the A-arm and torsion bars if your car is so equipped. Use the 17mm socket on two bolts an |
Gate Shift Installation
Author: Skip
The following is a brief overview of the installation process for 901/915 transaxles. 901 users must obtain a 915 shift housing. Complete instructions are included with |
KLA Strut Brace Installation - 911
Author: Skip
Installation :
Remove front strut bolt and rear inner strut bolt.
Place bracket, long leg of bracket toward front of car, over holes and replace bolts.
Tighten to about |
Window Express Kit Installation
Window Express Kit Installation Instructions.
Author: Skip
Find the Window Express Right Here.
Introduction
Most modern |
What is the Largest Wheel and Tire Combination I can get under my stock 914 fenders?
Author: Skip
One of the most commonly asked questions is, “ How much tire can I get under these fenders?” Well the 914 is not the most exact car ever built, and wheel well space varies a lot from |
Alternator Replacement
Author: Skip
The alternator is located in the driver's side engine compartment, under the air-flow meter (AFM), in front of the Turbo unit, and on top of the A/C compressor looking down into |
Brakes, front - 924S, 944, 944S
Author: Skip
Parts:
Rotors - Sebro Slotted ( OE Zimmerman or , gas-slotted and cross-drilled also available)
Pads - ( 944.351.951.02 E Pagid or Jurid , Mintex and KFP Magnum also av |
Brey-Krause Strut Brace Installation - 944
Author: Skip
Installation :
Open hood to gain access to the strut bearing mounting nuts.
There are (4) 13mm. strut bearing mounting nuts per side. Remove the (2) front and (1) inner |
Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
Clock/Bulb Replacement, digital, Late 944 and 968
Author: Skip
To get access to the clock light, do the following:
Remove the two air direction slider knobs on the heater controls face plate (leave on the round knobs).
Very carefully |
Clutch Replacement - Part One
Author: Skip
The following account explains in detail the procedure of changing a clutch in a 944/951. It also contains a list of tools, chemicals, parts and the sources where to find them. The |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Control Arm Bushing Upgrade - Weltmeister
Author: Skip
Weltmeister has produced several aftermarket solutions to Porsche suspensions for many years. This bushing kit is a replacement for the original equipment rubb |
Coolant Flush
Author: Skip
Got Milk? The coolant expansion tank on this series car can provide some warning signs of trouble deep within the engine. The oil cooler has seals that may break down o |
DME Chip Installation
Author: Skip
Location:
924S - located under the steering column - remove the four 8mm nuts holding it in.
85.5-91 944, 968 - located in the passenger-side foot well, behind the carp |
KLA Boxster Top Fix
Author: Skip
Boxster Lift Rod End Replacement Instructions:
Raise the tonneau cover to an upright position. This will be just before the top starts to pull back.
|
Motive Power Bleeder
Author: Skip
The Motive Products POWER BLEEDER TM works just like professional pressure bleeders -- at a fraction of the cost. With a POWER BLEEDER TM , one person can easily, safely, and |
