Brey-Krause Strut Brace Installation - 944
Author: Skip
Installation :
Open hood to gain access to the strut bearing mounting nuts.
There are (4) 13mm. strut bearing mounting nuts per side. Remove the (2) front and (1) inner |
KLA Strut Brace Installation - 924S, 944, 968
944 STRUT BRACE INSTALL
1) Remove 4 nuts holding strut
assembly to the body.
2) Place bracket over studs with
bracket upright toward front of car.
|
Pagid pads USED successfully at three major endurance races
Pagid pads USED successfully at three major
endurance races
24 Hr Race Le Mans
(France)
Pagid’s stopping
power and longevity pay of at the 2011 Le Mans 24h r |
KLA Strut Brace Installation - 964/993
Author: Skip KLA Strut Brace for 964/993 Installation: Remove 3 nuts holding strut assembly to the body. 2 nuts toward front of car. 1 rear/inner nut. Place bracket over studs with |
Seat Back Brace Installation Instructions
Seat Back Brace Installation Instructions To Order the I/O Port Seat Back Brace SBB-15 Click Here . Determine where on the seat back the mount needs to be to have the 1˝” tubing within ±20° from hori |
KLA Strut Brace Installation - 968/944 S2/944 S
1) Remove 4 nuts holding strut
assembly to the body.
2) Place bracket over studs with
bracket upright toward rear of car.
3) Replace washers
and nuts.& |
KLA Strut Brace Installation - 911
Author: Skip
Installation :
Remove front strut bolt and rear inner strut bolt.
Place bracket, long leg of bracket toward front of car, over holes and replace bolts.
Tighten to about |
Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
You know you're a racer when...
YOU KNOW YOU’RE A RACER WHEN:
-You think the primary purpose of wings is to PREVENT flight.
-You take your helmet along when you go buy new eyeglasses or check out cars
(seats).
-You feel |
PAGID race pad mounting and bedding in
Author: Pagid
PAGID race pad mounting and bedding in
MOUNTING NEW PADS ON USED DISCS (rotors)
We do not recommend using discs, which are pre |
Front Shock Replacement
Author: Skip
The 911, 914 and some 944’s featured a rebuildable front McPherson Strut. Instead of having to replace the entire strut unit, you will be able to merely replace the strut insert tha |
Control Arm Bushing Upgrade - Weltmeister
Author: Skip
Weltmeister has produced several aftermarket solutions to Porsche suspensions for many years. This bushing kit is a replacement for the original equipment rubb |
Control Arm, Front - Info
Author: Skip
924 mid 82 and older - stamped steel - VW/Audi part# 477.407.153F (left & right)
924 mid 82 and later, 924S, 944 83-85.1 - stamped steel - VW/Audi part# 171.407.153D &nbs |
K&N Air Filter Facts
Author: Skip
Why K&N Makes The World's Best Air Filters
Facts You Should Know About Air Filters
Paper vs K&N
Stock Replacement Filters
Washable and Reusable
Beyo |
Oil Cooling, Auxiliary
KISS ENGINEERING OIL COOLER KITS
944/944 TURBO
TEST DATA AND INFORMATION
COOLER &n |
Rear Wheel Bearing Replacement - late 944, 968
Discussion :
This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944 with aluminum trailing arms (1985.5 & later) |
Rod Bearing Replacement
Discussion:
This procedure will detail the steps necessary to replace the Rod Bearings on a 944 Turbo car. With some modifications it may also be applied to normally aspirated 944 |
Transaxle Fluid - Info
The Basics:
Friction Modifier (FM) is slippery stuff. The FM is in place to reduce LSD clutch chatter upon engagement. The amount needed is relative to the application and the age of |
Transaxle Replacement
Removal :
You will need to place the car up on jack stands at least 20”. Make sure that it is secure! Remove the rear wheels and the axles. If you have never had the axles |
3 - Basic Calculations
In the last two articles, we plunged right into some relatively complex issues, namely weight transfer and tyre adhesion. This month, we regroup and review some of the basic units and dimensions need |
