Window Express Kit Installation
Window Express Kit Installation Instructions.
Author: Skip
Find the Window Express Right Here.
Introduction
Most modern |
Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Short Shift Kit
Procedure :
Raise care on lift or place on jack stands. Make sure car is safely and securely supported, and you have plenty of room to see around the transaxle.
Locate the |
Brey Krause Deep Sump Oil Pan Spacer Kit for
Porsche 996, Boxster, Boxster S
Please follow our link for more information and purchasing the R-9095 Deep Sump Oil Pan Spacer Kit
|
AC Delete
I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products ($129 plus shipping). The kit consists of the aluminum factory alternator mounting bracket for non-A/C 944’s and a 6 |
Gate Shift Installation
Author: Skip
The following is a brief overview of the installation process for 901/915 transaxles. 901 users must obtain a 915 shift housing. Complete instructions are included with |
AC Delete
Author: Skip
I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products (Product Code: PP944.ACDEL.KIT1). The kit consists of the aluminum factory alternator mounting br |
Brakes, front - 924S, 944, 944S
Author: Skip
Parts:
Rotors - Sebro Slotted ( OE Zimmerman or , gas-slotted and cross-drilled also available)
Pads - ( 944.351.951.02 E Pagid or Jurid , Mintex and KFP Magnum also av |
Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
Clutch Replacement - Part One
Author: Skip
The following account explains in detail the procedure of changing a clutch in a 944/951. It also contains a list of tools, chemicals, parts and the sources where to find them. The |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Clutch Slave Bleeder Valve Remote
Author: Skip
A couple of years ago, while running at NHIS, I had some difficulty getting good, clean downshifts into second gear without double clutching. While some would attribute this to poo |
Control Arm Bushing Upgrade - Weltmeister
Author: Skip
Weltmeister has produced several aftermarket solutions to Porsche suspensions for many years. This bushing kit is a replacement for the original equipment rubb |
Ask Dr. Koni
Author: Skip
Question: What's the difference between the red Koni and the Sport Yellow Koni?
Answer: The valving is different. Sport Yellow units have stiffer valving than their St |
K&N Air Filter Facts
Author: Skip
Why K&N Makes The World's Best Air Filters
Facts You Should Know About Air Filters
Paper vs K&N
Stock Replacement Filters
Washable and Reusable
Beyo |
Koni Strut Conversion - 8641-1414S for late 944, 968
Author: Skip
Koni sealed strut insert conversion (8641-1414S)
Description
Image
Parts : Koni 8641-1414S Sport Struts - all conversion and instructions parts included.
|
Oil Cooling, Auxiliary
KISS ENGINEERING OIL COOLER KITS
944/944 TURBO
TEST DATA AND INFORMATION
COOLER &n |
Rear Wheel Bearing Replacement - 924, early 944
Parts needed: Rear Wheel Bearing Kit Stub Axel Nut/Rear Wheel Bearing Nut Moly Grease Procedure:
Lift rear or entire vehicle SAFELY!
Release handbrake
Remove the rear wheels.
Rem |
Rear Wheel Bearing Replacement - late 944, 968
Discussion :
This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944 with aluminum trailing arms (1985.5 & later) |
Rear Sway Bar Installation
This procedure is specifically for the installation of a 968 M030 Sway Bar but also applies to any 924/944/968 factory sway bar.
The best (easiest) way to remove or install the sway bar is with |
