Front Shock Replacement
Author: Skip
The 911, 914 and some 944’s featured a rebuildable front McPherson Strut. Instead of having to replace the entire strut unit, you will be able to merely replace the strut insert tha |
OXS light reset
OXS light reset < 911 < Main Page
OXS light reset
Author: Skip
For those 911's equipped with the "OXS" warning lamp, you can reset or disable this on your own. Here's how:
- the OXS lam |
Window Express Kit Installation
Window Express Kit Installation Instructions.
Author: Skip
Find the Window Express Right Here.
Introduction
Most modern |
What is the Largest Wheel and Tire Combination I can get under my stock 914 fenders?
Author: Skip
One of the most commonly asked questions is, “ How much tire can I get under these fenders?” Well the 914 is not the most exact car ever built, and wheel well space varies a lot from |
Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Alternator Replacement
Author: Skip
The alternator is located in the driver's side engine compartment, under the air-flow meter (AFM), in front of the Turbo unit, and on top of the A/C compressor looking down into |
Brakes, front - 924S, 944, 944S
Author: Skip
Parts:
Rotors - Sebro Slotted ( OE Zimmerman or , gas-slotted and cross-drilled also available)
Pads - ( 944.351.951.02 E Pagid or Jurid , Mintex and KFP Magnum also av |
Brey-Krause Strut Brace Installation - 944
Author: Skip
Installation :
Open hood to gain access to the strut bearing mounting nuts.
There are (4) 13mm. strut bearing mounting nuts per side. Remove the (2) front and (1) inner |
Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
Clock/Bulb Replacement, digital, Late 944 and 968
Author: Skip
To get access to the clock light, do the following:
Remove the two air direction slider knobs on the heater controls face plate (leave on the round knobs).
Very carefully |
Clutch Replacement - Part One
Author: Skip
The following account explains in detail the procedure of changing a clutch in a 944/951. It also contains a list of tools, chemicals, parts and the sources where to find them. The |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Clutch Slave Bleeder Valve Remote
Author: Skip
A couple of years ago, while running at NHIS, I had some difficulty getting good, clean downshifts into second gear without double clutching. While some would attribute this to poo |
Control Arm Bushing Upgrade - Weltmeister
Author: Skip
Weltmeister has produced several aftermarket solutions to Porsche suspensions for many years. This bushing kit is a replacement for the original equipment rubb |
Control Arm, Front - Info
Author: Skip
924 mid 82 and older - stamped steel - VW/Audi part# 477.407.153F (left & right)
924 mid 82 and later, 924S, 944 83-85.1 - stamped steel - VW/Audi part# 171.407.153D &nbs |
KLA Boxster Top Fix
Author: Skip
Boxster Lift Rod End Replacement Instructions:
Raise the tonneau cover to an upright position. This will be just before the top starts to pull back.
|
Motive Power Bleeder
Author: Skip
The Motive Products POWER BLEEDER TM works just like professional pressure bleeders -- at a fraction of the cost. With a POWER BLEEDER TM , one person can easily, safely, and |
Porsche Option Codes
Author: Skip
Code
Description
009
3 speed sportomatic transmission
018
Sport steering wheel with elevated hub
020
Speedometer with 2 scales KP |
Portable air tank tips
Author: Skip
Go ahead and laugh, but if this helps just one person...
Many of us have the small portable air tanks for various tasks, most for quick racing tire pressure changes. Frust |
Sway Bar Calculations
Author: Skip
Provided by KLA Industries to answer the question of how the drop-link length affects the rate of a sway bar.
Here is the angle of the dangle formulas for calculating the ch |
