Knowledge Base:  

You are here: Knowledge Base : Unit
Page of 2
Oil Pressure Sending Unit Replacement
  Oil Sender Unit for 928/944/968/964/993 The oil pressure sending unit is located just under the oil filter, underneath the car in the front area on the passenger side.  Jack car up
Front Shock Replacement
Author: Skip The 911, 914 and some 944’s featured a rebuildable front McPherson Strut. Instead of having to replace the entire strut unit, you will be able to merely replace the strut insert tha
AC Delete
I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products ($129 plus shipping). The kit consists of the aluminum factory alternator mounting bracket for non-A/C 944’s and a 6
OXS light reset
OXS light reset < 911 < Main Page OXS light reset Author: Skip For those 911's equipped with the "OXS" warning lamp, you can reset or disable this on your own. Here's how: - the OXS lam
Window Express Kit Installation
Window Express Kit Installation Instructions. Author: Skip Find the Window Express Right Here. Introduction Most modern
AC Delete
Author: Skip I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products (Product Code: PP944.ACDEL.KIT1). The kit consists of the aluminum factory alternator mounting br
Accusump Installation
Author: Skip I know of few topics that elicit such dismissive and strongly held opinions as that of how to eliminate the cause of #2 rod bearing failure in 944 engines. Some builders claim that
Alternator Replacement
Author: Skip The alternator is located in the driver's side engine compartment, under the air-flow meter (AFM), in front of the Turbo unit, and on top of the A/C compressor looking down into
Camber Plate Installation (Paragon)
Author: Skip   Your new Racers Edge Camber Plates will bolt in without modification.   After jacking up your car and supporting it on jack stands, remove the wheel/t
Clock/Bulb Replacement, digital, Late 944 and 968
Author: Skip To get access to the clock light, do the following: Remove the two air direction slider knobs on the heater controls face plate (leave on the round knobs). Very carefully
Clutch Replacement - Part One
Author: Skip The following account explains in detail the procedure of changing a clutch in a 944/951. It also contains a list of tools, chemicals, parts and the sources where to find them. The
Clutch Replacement - Part Two
Author: Skip TRANSMISSION: Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea
Clutch Slave Bleeder Valve Remote
Author: Skip A couple of years ago, while running at NHIS, I had some difficulty getting good, clean downshifts into second gear without double clutching. While some would attribute this to poo
Motive Power Bleeder
Author: Skip The Motive Products POWER BLEEDER TM works just like professional pressure bleeders -- at a fraction of the cost.  With a POWER BLEEDER TM , one person can easily, safely, and
Porsche Option Codes
Author: Skip Code Description 009 3 speed sportomatic transmission 018 Sport steering wheel with elevated hub 020 Speedometer with 2 scales KP
Ask Dr. Koni
Author: Skip   Question: What's the difference between the red Koni and the Sport Yellow Koni? Answer: The valving is different. Sport Yellow units have stiffer valving than their St
K&N Air Filter Facts
Author: Skip Why K&N Makes The World's Best Air Filters Facts You Should Know About Air Filters Paper vs K&N Stock Replacement Filters Washable and Reusable Beyo
Dash Replacement
Introduction Replacing the dash on a late model, 85.5 and newer Porsche 944, is not a difficult task.   It is very time consuming and meticulous.   Patience is necessary.   An ex
What is Tech-Session.com? How can I help?
Hello, and welcome to the Paragon Products Tech-Session. This site is here for you. The enthusiast, the hobbyist, the Porsche owner! We're small now, but growing quickly. Paragon friends and customers
Fuel Level Sender
Author: Skip Running out of gas when the indicator says you still have a quarter-tank?  Could be the Fuel Level Sender within the gas tank is out of calibration, or, the Fuel Gauge itself