Koni Adjustment Procedures
Author: Skip
Koni Adjustment Procedures
3011/3012
28 Series
Sport (yellow)
3011/3012
NOTE:
Do not place shock absorber in a vice (exc |
Rear Ride Height Adjustment
Porsche 924/944/968 rear ride height can be lowered (in most cases) by approximately ¾" using the following procedure. This adjustment was originally designed for factory ride height settings across |
Gate Shift Installation
Author: Skip
The following is a brief overview of the installation process for 901/915 transaxles. 901 users must obtain a 915 shift housing. Complete instructions are included with |
Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
KLA Boxster Top Fix
Author: Skip
Boxster Lift Rod End Replacement Instructions:
Raise the tonneau cover to an upright position. This will be just before the top starts to pull back.
|
Porsche Option Codes
Author: Skip
Code
Description
009
3 speed sportomatic transmission
018
Sport steering wheel with elevated hub
020
Speedometer with 2 scales KP |
Sway Bar Calculations
Author: Skip
Provided by KLA Industries to answer the question of how the drop-link length affects the rate of a sway bar.
Here is the angle of the dangle formulas for calculating the ch |
Ask Dr. Koni
Author: Skip
Question: What's the difference between the red Koni and the Sport Yellow Koni?
Answer: The valving is different. Sport Yellow units have stiffer valving than their St |
K&N Air Filter Facts
Author: Skip
Why K&N Makes The World's Best Air Filters
Facts You Should Know About Air Filters
Paper vs K&N
Stock Replacement Filters
Washable and Reusable
Beyo |
Short Shift Kit
Procedure :
Raise care on lift or place on jack stands. Make sure car is safely and securely supported, and you have plenty of room to see around the transaxle.
Locate the |
Throttle Position Sensor
Find the Throttle Position Sensor You Need Right Here.
Discussion:
The Throttle Position Sensor (TPS) is used to report various throttle positions to the DME. A very common failure item on t |
Torsion Bar Replacement
Information for what Torsion Bars to Use Please Click Here . Be warned that torsion bar replacement for a 944 is not a job for the faint of heart. In fact even experienced specialists wil |
Transaxle Replacement
Removal :
You will need to place the car up on jack stands at least 20”. Make sure that it is secure! Remove the rear wheels and the axles. If you have never had the axles |
Ride Height Measurement
Torsion Bar Indexing 101
The outside has 44 splines (teeth)
Every tooth you move the outside splines you move the spring plate about 9 degrees.
The inside has 40 splines (teeth)
Every |
2 - Keeping Your Tyres Stuck to the Ground
In last month's article, we explained the physics behind weight transfer. That is, we explained why braking shifts weight to the front of the car, accelerating shifts weight to the rear, an |
Seat Back Brace Installation Instructions
Seat Back Brace Installation Instructions To Order the I/O Port Seat Back Brace SBB-15 Click Here . Determine where on the seat back the mount needs to be to have the 1½” tubing within ±20° from hori |
Tarett Engineering Rear Sway Bar Installation Instructions
REAR SWAY BAR ASSEMBLY INSTRUCTIONS 1) Tarett Engineering rear sway bars are designed to mount directly to the factory mounting brackets on 1965-89 911’s, 912’s & 930’s. Any cars without factory m |
