KLA Strut Brace Installation - 968/944 S2/944 S
1) Remove 4 nuts holding strut
assembly to the body.
2) Place bracket over studs with
bracket upright toward rear of car.
3) Replace washers
and nuts.& |
Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Clutch Replacement - Part One
Author: Skip
The following account explains in detail the procedure of changing a clutch in a 944/951. It also contains a list of tools, chemicals, parts and the sources where to find them. The |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Control Arm, Front - Info
Author: Skip
924 mid 82 and older - stamped steel - VW/Audi part# 477.407.153F (left & right)
924 mid 82 and later, 924S, 944 83-85.1 - stamped steel - VW/Audi part# 171.407.153D &nbs |
Ask Dr. Koni
Author: Skip
Question: What's the difference between the red Koni and the Sport Yellow Koni?
Answer: The valving is different. Sport Yellow units have stiffer valving than their St |
Engine Production
Author: Skip
Engine : (USA values - to locate the "code", look for another Tech-Session article regarding Engine Identification )
944 - 8 Valve, Normally Aspirated
MY
Co |
Odometer Gear Replacement - late 944
Author: Skip
Instructions :
Remove 9 screws holding front/back together:
Remove 4 screws holding speedometer in housing:
Gently pull off speedometer needle and remove 2 screws holdi |
Rear Ride Height Adjustment
Porsche 924/944/968 rear ride height can be lowered (in most cases) by approximately ¾" using the following procedure. This adjustment was originally designed for factory ride height settings across |
Porsche Chronology
Some model history that may help with shopping our site
Model
Year
Engine
Note
356
55-65
911
|
Rear Spring Rates vs. Effective Rates
An effective spring rate is the value when taking into consideration the placement, construction, and type of the sprung materials.
Torsion bar diameter is expressed as the effective diameter.&nbs |
Rear Wheel Bearing Replacement - late 944, 968
Discussion :
This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944 with aluminum trailing arms (1985.5 & later) |
Rod Bearing Replacement
Discussion:
This procedure will detail the steps necessary to replace the Rod Bearings on a 944 Turbo car. With some modifications it may also be applied to normally aspirated 944 |
Short Shift Kit
Procedure :
Raise care on lift or place on jack stands. Make sure car is safely and securely supported, and you have plenty of room to see around the transaxle.
Locate the |
Throttle Position Sensor
Find the Throttle Position Sensor You Need Right Here.
Discussion:
The Throttle Position Sensor (TPS) is used to report various throttle positions to the DME. A very common failure item on t |
Sway Bars - Info
For information on 944 Sway Bars and Parts for Sway Bars Click Here . Hi folks - just a friendly reminder that these cars are getting a little old, and previous owners do crazy things... somet |
Koni Strut Conversion - 8641-1414S
Koni Strut Conversion - 8641-1414S This procedure applies to the following Porsche models: 1987-89 944 1987-88 944S 1989-91 944S2 1986-88 944 Turbo 1992-95 968 |
Pagid Brake Pads - FAQ
Author: Skip
Brake Pad FAQ
Question: What's with the different compounds? What is the application of each?
PAGID RS packaging
RS 7: Black (Discontiu |
